SGTKJSJS m.2 ssd Screws Kit, Nvme M2 Screws Suitable for Asus ASRock Gigabyte MSI Motherboard & Nvme SSD

For whatever reasons, manufacturers of M.2 devices "forget" to include the stud and screw needed to install the device to the computer instrument it needs to be attached to.Amazon sells several of these kits, in different configurations.In my experience, this is the better of these kits.Depending on your hardware, there are several different size fasteners needed for the task. Some other kits give you enough hardware for one or two installations, but not necessarily the right sizes. This kit comes with three sets in three sizes. When installing the M.2 device, start wit the new M.2 safely in the package it was dispensed to you. Instead, find a little magnet, and spread all the pieces in the magnetic tray or over the dace of a magnet. Then, with a good light, a dose of patience, and perhaps a magnifying lens (as your age and health dictate). Find the area of your computer (Mother-Board) where the card is supposed to be mounted and study it a bit. A YouTube short presentation may help. This system is a bit unusual and it will not hurt to get acquainted with all the participants before the fin begins.Next, install the heat-sink to the device, paying attention to pesky details.(Assuming the <.2 device is to be mounted parallel to the MB), measure the length of the M.2. This will hel0p you decide which mounting hole to use. Almost without exception, you will need a stud; the M.2 needs to go over the mounting holes/bases pput there for the shorter sizes. Going over them without touching; the studs are metal, the bottom of the M.2 is full of signal traces, metal to metal contact means trouble, etc.Install the stud in the appropriate hole. Finger tight is good enough, unless you have the proper tools.Next, the M.2 card needs to be gently inserted into the special socket (about 30 degrees angle), and then gentlylowered onto the stud you just finger-tightened above.Hold the M.2 down and start a screw into the stud. fasten the screw gently. No need to torque anything, jsut tight enough so normal handling will not loosen it.Suggestion: Get yourself a tiny magnet. If it is small enough, attach it to the shaft of the tiny screwdriver that came with the kit. If not, try to rub the screwdriver with the magnet, a few times, but not back and forth. The goal is to make the screwdriver slightly magnetized. This way you will be able to pick up the screw with the screwdriver. Whatever you do, do NOT drop the screw or the stud into a crevice in the computer. If you do manage to do that, make absolutely sure you find the screw before you apply power to that computer.None of this has anything to do with this kit, but it is information surprisingly many do not possess.

I was adding a solid state M2 drive to my computer, and I did not have the support post and screw to secure it. I found this on Amazon and ordered it. It was exactly what I needed. If you have never installed an NVME M2 drive, (flat memory chip that takes the place of your computer's hard drive) it can be a little tricky. The NVME chip has a notch, and the spacer post grooves into the notch and a tiny screw holds the whole thing tight. Without those two pieces there is not practical way to secure NVME M2 in its slot. These were machined to perfection and was an easy install. Oh, and the kit includes 9 variable sized posts, 9 screws and a cheap little screwdriver. Good kit highly recommended.

Fit my Msi mobo

Price was on point at around 5 bucks. Versatile m.2 screw and stand-off kit! I thought I just needed a m.2 2.5mm screw but my nvme was slanted so I’m glad I ordered these because the standoff for Asus mobos fit perfect and level. I also had a gigabyte Mobo I was working on and these came in clutch, highly recommended.

Other than the screwdriver that immediately broke they have worked just fine, only wish I had order a set with more screws.

Worked for my Aorus Elite X570 motherboard by Gigabyte. The included Screw in the 110 standoff stripped after removing slowly counter clockwise forcing me to order a replacement set inorder to finish populating my M.2 slots in my build. I used both a standoff and a screw included with this set and everything worked as intended. The standoff is equal hight, matching the factory Standoffs produced by Gigabyte. Was able to install my second M.2 Cover and place my 3090 strix which has a low lying cooler and had no issue with height or clearance with this third party set. If you have a board produced by Gigabyte I can confirm that the standoffs and screws are a match

Bought a pre-built and was excited to install another much larger m.2 SSD only to find out that I didn’t have the screws to hold it in place on my ASRock MB. Found this in 5 minutes, ordered it, arrived next day and install was literally 2 minutes with provided screw driver and screw.Thank you!

My motherboard has 2 M.2 NVME slots but only came with one standoff screw, because somehow the vendor thought that made sense. These work perfectly for the intended purpose and I now have several extra on hand in case I need them. It seems these aren't easy to come by at your typical brick and mortar or other online retailers (in my personal experience). Found them here, received them quickly, and had them when I needed them to complete my build.